بهبود روش تعیین ضریب شکل مخازن سدها و بررسی تغییرات آن در اثر رسوب گذاری

نوع مقاله : مقالات پژوهشی

نویسندگان

دانشگاه صنعتی اصفهان

چکیده

چکیده
ضریب شکل یکی از مهمترین خصوصیات فیزیکی مخازن سدها می باشد که عبارت است از عکس شیب منحنی ارتفاع - حجم مخزن در دستگاه مختصات لگاریتمی. از ضریب شکل برای طبقه بندی مخازن و پیش بینی توزیع رسوب در آن‌ها استفاده می‌شود. در این تحقیق یک روش جدید جهت بهبود تعیین ضریب شکل مخازن ارائه شده است. در روش پیشنهادی، به جای منحنی ارتفاع - حجم، منحنی بدون بعد ارتفاع - حجم مخزن در مختصات تمام لگاریتمی ترسیم می شود و سپس مقدار ضریب شکل تعیین می گردد. داده های ارتفاع - حجم اولیه و داده های حاصل از رسوب سنجی های انجام شده در مخازن 4 سد در ایران (دز، شهید عباسپور، کارده و لتیان) و 4 سد در آمریکا (روزولت، سدار بلاف، کروین و نامبی فالز) استفاده شده است. نتایج نشان می دهد که ضرایب شکل همه مخازن مورد مطالعه، در اولین یا دومین عملیات رسوب سنجی کم شده، به گونه ای که مقدار عددی آن‌ها به 2 تا 5/2 کاهش یافته است. همچنین تیپ همه مخازن پس از رسوب گذاری به تیپ III تغیر پیدا کرده است. لذا بهتر است برای کاربرد روش کاهش سطح در توزیع رسوبات، تیپ مخازن از نوع III انتخاب شود. از مهمترین مزایای روش جدید این است که به طور هم‌زمان می توان منحنی های بدون بعد ارتفاع - حجم چندین مخزن (و یا یک مخزن در رسوب سنجی های متعدد) را در یک دستگاه مختصات لگاریتمی ترسیم نموده و ضریب شکل آن‌ها را با هم مقایسه کرد. در حالی که در روش قدیمی بایستی منحنی ارتفاع - حجم مخزن هر سد را به طور جداگانه در یک دستگاه مختصات لگاریتمی ترسیم نمود.

واژه های کلیدی: توزیع رسوب، روش افزایش سطح، روش کاهش سطح، منحنی ارتفاع – حجم

عنوان مقاله [English]

Improvement of the reservoir shape factor method and evaluation of its changes due to sedimentation

نویسندگان [English]

  • J. Mohammadzadeh Habili
  • S.F. Mousavi
College of Agriculture, Isfahan University of Technology, Isfahan
چکیده [English]

Abstract
The shape factor is one of the most important physical characteristics of a dam’s reservoir. This factor is equal to the reciprocal of the slope of a line obtained by plotting reservoir depth against reservoir capacity on a log-log paper. The shape factor is used for reservoir classification and sediment distribution. In this study, a new method is proposed for determination of the reservoir shape factor. In this method, the normalized depth-capacity curve is plotted on log-log paper and then the value of shape factor could be derived as the reciprocal of the line slope. In this study, the original depth-capacity data and reservoir sedimentation data of 4 dams in Iran (Dez, Kardeh, Latian and Shahid Abbaspour) and 4 dams in the USA (Cedar Bluff, Kirwin, Nambe Falls, and Theodore Roosevelt) were used. The results showed that reservoir shape factor of all reservoirs decreased 2 to 2.5 for the first or second sedimentation measurements. In addition, the type of reservoirs was changed to type III. Therefore, prediction of reservoir sedimentation by area reduction method should be performed with reservoir type III. The most important advantage of the proposed method is the capability of plotting and comparing the normalized depth-capacity data of several reservoirs (or several sedimentation measurements of a single reservoir) on individual log-log paper. While in the old method, the depth-capacity data of each reservoir should be plotted on a separate log-log paper.

Key words: Reservoir, Sediment distribution, Area-increment method, Area-reduction method, Depth-capacity curve

CAPTCHA Image