تأثیر شکل دهانه آبگیر بر مقدار ضرایب انرژی و اندازه حرکت و ابعاد جداشدگی جریان

نوع مقاله : مقالات پژوهشی

نویسندگان

1 دانشگاه پیام نور

2 آزاد استهبان

3 پیام نور

چکیده

هنگامی که جریان در یک کانال اصلی یا رودخانه به نزدیکی آبگیر می‌رسد، خطوط جریان به سمت آبگیر منحرف می‌شوند. در این حالت یک ناحیه جداشدگی جریان در آبگیر ایجاد می‌شود که به علت کاهش عرض جریان انحرافی باعث کاهش دبی و راندمان آبگیری می‌گردد. در این تحقیق برای تعیین شعاع بهینه ورودی آبگیر، آزمایشاتی بر روی آبگیر جانبی منشعب از کانال مستطیلی با ورودی گردشده با سه نسبت شعاع r/Wb برابر 4/0، 6/0 و 8/0 (r شعاع دهانه ورودی و Wb عرض آبگیر) انجام و ابعاد منطقه جداشدگی و همچنین ضرایب انرژی و اندازه حرکت در دهانه آبگیر محاسبه گردید. این آزمایشات در شرایط جریان انتها بسته و انتها باز در نسبت دبی انحرافی 2/0، 4/0، 6/0 و 8/0 انجام شد. با رسم خطوط جریان توسط نرم‌افزار Tecplot برای شرایط مختلف، مقدار طول و عرض جداشدگی تعیین و در نهایت اندازه جداشدگی برای نسبت شعاع 8/0 کمتر از شعاع دیگر بدست آمد. بنابراین نسبت r/Wb برابر 8/0 با کمترین مقدار جداشدگی به عنوان نسبت شعاع بهینه انتخاب گردید.

کلیدواژه‌ها


عنوان مقاله [English]

Effect of Mouth Shape on the Energy and Momentum Coefficients and Flow Separation Dimensions

نویسندگان [English]

  • mehdi karami moghadam 1
  • tooraj sabzevari 2
  • mehdi nourzadeh hadad 3
1 payam noor
2 azad university
3 payam noor
چکیده [English]

Introduction: The study of flow diversion in open channels which has been, since long, under consideration by hydraulic engineers, is much used to divert flow from a main channel or from a river into an irrigation or hydropower channel. When a water intake with an angle is installed at one side of the channel, the streamlines of the flow deflect towards the intake. As a result, a separation zone is produced in the lateral channel. The separation zone develops in the lateral channel and reduces the discharge capacity and efficiency of water intake by delimiting the channel width available for the flow. Therefore, determination of water intake geometry and flow conditions to produce minimum separation zone is very important and they are the focus of this study. The majority of previous studies was conducted on sharp edged water intake entrances. Therefore, in this study, to find the optimum radius for a round edged entrance water intake, a comprehensive experimental program was carried out in a laboratory flume and the separation zone dimensions and Alpha and Beta coefficients were measured.
Materials and Methods: The experimental model was built in hydraulics laboratory. The water intake was installed at 55 degrees to the main channel. The main channel consisted of a rectangular cross-section with a base width of 0.5 m, height of 0.4 m and a length of 15.80 m. The lateral diversion channel was 0.25 m wide, 0.40 m high. According to previous experiments that performed by Keshavarzi and Habibi (2005), radii of 10, 15 and 20 cm were selected for the edges of the intakes, upstream of the 55 degree water intake. The velocities of the flow in transverse and flow directions were measured using an electromagnetic velocity meter at three distances Z= 3 cm, 6 cm and 12 cm, in which Z is the distance from the bed. Then the size of the separation zone, Alpha and Beta coefficients were determined.
Results and Discussion: To find a relationship between the radius of the round edge entrance in the 55 degree water intake and the size of separation, the geometry of the separation zone must be determined. To find the geometry and pattern of separation zone for different flow conditions, the particle traces technique was employed using Tec plot Software version 8.0. In open end flow condition, for discharge ratios of 0.2, 0.4, 0.6 and 0.8, and for the radii of 10, 15 and 20 cm, flow separation occurs at 3 cm and 12 cm distance and only upstream of the intake inlet. The separation size in r=20 cm is less than for other radii. Also, the separation size for Qr = 0.8 is minimized and for Qr =0.2 is the maximum and for r/Wb=0.8, the length and width of separation are minimum. In close end flow condition and for radii of 10, 15 and 20 cm, the size of separation zone at upstream of water intake is much larger than that in downstream. Comparing with the separation length downstream of the intake it can be concluded that with increasing the inlet radius, the separation length upstream of the intake inlet decreases. Therefore, in close end conditions, rounding of the intake inlet is effective to decrease separation length at upstream side of water intake. Also, in close end conditions, flow separation occurs at downstream side of water intake. Furthermore, the separation size for r=20 cm is less than for other radii, therefore, r/Wb=0.8 is the optimum radius ratio with a minimum separation size at the 55 degree water intake.
Conclusions: When a water intake with an angle is installed at one side of the channel, the streamlines of the flow deflect towards the intake. As a result, a separation zone is produced in the lateral channel. The separation zone development in the lateral channel and reduces the discharge capacity and efficiency of water intake by delimiting the channel width available for the flow. In this study, to find the optimum round inlet radius, the experimental tests were carried out at a water intake installed in a rectangular channel with rounded edge with 10, 15 and 20 cm inlet radius. Then separation zone dimensions and alpha and beta coefficients determined. These experiments were carried out in close end and open end flow conditions for diversion flow ratio 0.2, 0.4, 0.6 and 0.8. Using particle trace plot for different flow pattern, the values of length and width of flow separation upstream and downstream of the intake were determined. The result showed that the separation size for Qr = 0.8 is minimized, whereas it is maximum for Qr =0.2. Furthermore, the separation size for r=20 cm is less than for other radius, therefore, r/Wb=0.8 with a minimum separation size was selected as the optimum radius ratio.

کلیدواژه‌ها [English]

  • Efficiency
  • Optimum radius
  • Radius of entrance
  • Rectangular channel
1- Abbasi A.A., and Maleknejad Yazdi M. 2014. The impact of sill and submerged vanes on sediment laden flow at lateral intake. The Iranian Society of Irrigation and Water. 4(16):104-116. (in Persian with English abstract)
2- Abolghasemi M., Ghodsian M., and Sangin Abadi H. 2013. The effects of flow diversion on sediments entering the intake in 52 deg. diversion angle in sinus river. Journal of hydraulic, 6(1): 41-52. (in Persian)
3- Best J.L., and Reid I. 1984. Separation zone open-channel junctions. Journal of Hydraulic Engineering, ASCE. 110(11): 1588-1594.
4- Esmaeili Varaki M., Farhoudi J., and Walker D. 2009. Investigation of flow at a right-angle lateral intake. ICE, Journal of Water Managemet, 162 (6):379-388.
5- Jalili H.R., Hoseinzade Dalir A., and Farsadizadeh D. 2011. Effect of intake geometry on the sediment transport and flow pattern at lateral intake. Iranian Water Research Journal. 5(9): 1-10. (in Persian)
6- Jalili H.R., Hoseinzade Dalir A., and Farsadizadeh D. 2012. Effect of mouth shape on the flow pattern and sedimentation in the vertical lateral diversion. Journal of Water and Soil, 25(6):1321-1331. (in Persian with English abstract)
7- Jalili H.R., Hoseinzade Dalir A., and Farsadizadeh D. 2013. Investigating effect of inlet shape on the flow pattern and vortex generation around inlet of intake using numerical model. Journal of Water and Soil Science. 24(1):29-40. (in Persian with English abstract)
8- Karami Moghadam M., Shafai Bajestan M., and Sedghi H. 2013. Experimental investigation of sediment entry to an intake installed at a main channel with inclined bank. Iran-Water Resources Research, 8 (3):54-65. (in Persian with English abstract)
9- Keshavarzi A., and Habibi L. 2005. Optimizing water intake angle by flow separation analysis.Journal of Irrigation and Drainage. 54(4): 543-552.
10- Montaseri H., and Asiaei H. 2014. Validating of SSIIM 3D model for flow field simulation in a U shape channel bend with intake. Journal of Water and Soil Conservation, 21(4):29-53. (in Persian with English abstract)
11- Neary V.S., and Odgaard A.J. 1993. Three dimensional flow structure at open channel diversions. Journal of Hydraulic Engineering, ASCE, 119(11): 1223-1230.
12- Ramamurthy A.S., Junying Q., and Diep V. 2007. Numerical and experimental study of dividing open-channel flows.Journal of Hydraulic Engineering, ASCE. 133(10): 1135–1144.
13- Shamsodini-nejad A. 2001. Investigating effect of secondary currents on the sedimentation at lateral intake and sediment control with phisics model. M.S Thesies, College of Agriculture, Shiraz University. (in Persian with English abstract)
CAPTCHA Image