دوماه نامه

نوع مقاله : مقالات پژوهشی

نویسندگان

1 دانشگاه تبریز

2 دانشگاه تبریز- گروه آبیاری

چکیده

سرریزهای لبه تیز مرکب اغلب به منظور اندازه گیری دامنه وسیعی از جریان با دقت مناسب در کانال های روباز مورد استفاده قرار می گیرد. در این تحقیق آزمایش هایی به منظور بررسی میزان تأثیر عرض دهانه مستطیلی، ارتفاع تاج سرریز و ارتفاع دهانه قوس دایره ای بر ضریب دبی جریان آزاد بر روی سرریزهای مرکب قوس دایره ای- مستطیلی در فلوم آزمایشگاهی انجام گرفت. مشخصات سرریزهای مرکب مورد استفاده شامل عرض دهانه مستطیلی 15، 20 و 25 سانتی متر، ارتفاع تاج سرریز 15، 20 و 25 سانتی متر و ارتفاع دهانه قوس دایره ای 5، 5/7، 10 و 50/12 سانتی متر می باشند. نتایج نشان داد بر اساس داده های آزمایشگاهی، تغییرات ضریب دبی جریان در سرریزهای مرکب مذکور در محدوده 54/0 تا 89/0 می باشد. به ازای بار آبی معین با افزایش عرض دهانه مستطیلی، ضریب دبی جریان در حدود 2 تا 10 درصد افزایش می یابد. با افزایش ارتفاع تاج سرریز، میزان کاهش ضریب دبی جریان در حدود 1 تا 5 درصد می باشد. به ازای بار آبی معین با تغییر ارتفاع دهانه قوس دایره ای، ضریب دبی جریان سرریزهای مرکب نسبت به سرریزهای مستطیلی ساده در حدود 35 درصد افزایش می یابد. مقادیر محاسباتی و مشاهداتی ضریب دبی جریان بر اساس معیارهای ارزیابی ضریب تبیین ((R2 و جذر میانگین مربعات خطا (RMSE)که به ترتیب برابر با 630/0 و 061/0 محاسبه گردیدند، مورد مقایسه قرار گرفت. نتایج به دست آمده نشان داد که استفاده از ترکیب خطی روابط جریان در سرریزهای لبه تیز دایره ای و مستطیلی شکل، با دقت قابل قبولی قادر به برآورد ضریب دبی جریان سرریزهای مرکب می باشد.

کلیدواژه‌ها

عنوان مقاله [English]

Investigation of Effective Parameters on Discharge Coefficient of Compound Arched Circular-Rectangular Sharp-Crested Weirs

نویسندگان [English]

  • S.N. Mousavi 1
  • Davoud Farsadi 2
  • H. Arvanaghi 1
  • A. Abbaspour 1

1 Tabriz of University

2

چکیده [English]

Introduction: The compound sharp-crested weirs are composed from several notches and those are designedin different shapes. One of the hydraulic advantagesof compound weirs is that atlowflow rate, the bottomnotchacts assimpleweir andwith the creation of morehydraulicheadonits upstream, due to theshape of thenotch, make dischargemeasurement withappropriatesensitivity. In high flow rates, the upper notch prevents of increasing upstream water level and backwater and discharge measurement is possible with acceptable accuracy. The compound sharp-crested weirs can be used as an appropriate solution for discharge measurement with reasonable accuracy and sensitivity of the extensive range of flows. Relations are derived from this kind of weirs hassufficientaccuracy withobservation of design criteriaandconstructionstandards. The purposeofthisresearch was a laboratory investigation of geometricandhydraulic effective parameterson discharge coefficient of compound arched circular- rectangular sharp-crested weirs in two cases of full width of channel and partially contracted weirs and compare the values of the discharge coefficient of compound and simple rectangular weirs.
Materials and Methods:Considering the geometric, kinematic and dynamic variables affecting the free flow of sharp-crested weirs, there are 11independent variableswiththree main quantities (length, massandtime). Usingdimensional analysis with π-Buckinghammethod,it can bederived thedimansionlessrelationship. In order to assess theeffect of various parametersonthe coefficient ofCd,thedimansionlessdiagramsare used. Inthe state of(h≤h0), discharge relationship usedinsimplecircular weir. In thestate of(h>h0), discharge of compound weir is computeted from the linear combination of discharge relationships in circular and rectangular weirs. Experimentsare conducted inthe hydraulic engineering models laboratory, Department of Water Engineering, University of Tabriz, in a rectangular glass-metal flume of 9 m length, 25 cm width and 50 cm height. Aftersetting up the weirs in a relevant place of flume andestablish thesteady flow,experiments were performedinthefree flowon36 models of weirs.
Results and Discussion:In this research, theeffects ofrectangularnotch width, the height of weir crest, the height ofcirculararch notch were investigated forchanges of headwithdimensionless ratios of h/P,h/R,h/h_0 ,h/Bon discharge coefficient. The results showthat fora known headover the weir, discharge coefficient increase about 2 to 10percent with the development of the rectangular notch width of compound and simple rectangular sharp-crested weirs. For a given head over the weir, discharge coefficient decrease approximately 1 to 5percent by increasing the height of the weir crest of compound and simple sharp-crested weirs. Fora given head over weir in low head values, discharge coefficient increase approximately 35percent by reducing the height of circulararch notch in the compound weirs than simple rectangular weirs. Based on statistical indicators, computational and observation discharge coefficient values in most compound and simple weirs, acceptable coincidence with each other. The meanvalues of thecoefficient of determination (R2) androot mean square error(RMSE) are 0.630and0.061,respectively. Among the effective factors that indicate the difference, it can be referred to the theoretical equation in the compound state that is obtained by assuming a linear combination of simple weirs. The effect of the lateral walls of the flume, the measurement accuracy of hydraulic head and discharge, the conditions of flow entrance, the extension of the range of empirical equations proposed in literature for discharge coefficient of simple weirs, Other factors contributing to the difference between the estimated and observed values of discharge coefficient. Inthistypeofweirs,the least amount ofdiscontinuityin thetransition region of simple to compound state in head-discharge relationship can be seenin thewide rangeofdischargescomparedwithother kinds ofcompound weirswithhorizontalorslopingcrests.
Conclusion:In this research, a seri of experiments conducted to investigate Cd of the compound arched circular-rectangular sharp-crested weirs in both full width of the channel and partially contracted. The advantage of these weirsisdischarge measurement ina wide range. According to the parametersaffecting theweir, Cd has changed from 0.54 to 0.89 range in the compound weirs and 0.55 to 0.66 range in the simple rectangular weirs. Bychanging the weir specifications, Cd increase about 35 percentthan thesimplerectangular weir. Forchanges of the head by usingthe experimental data, the discharge continuityofthistypeofweir is far more thanthecompound weirs withhorizontal orinclined crests. Based on theevaluation criteria, using alinear combinationofthe discharge relationshipof circularandrectangularsharp-crested weirs, be able to estimate Cd of the compound weirs withacceptable accuracy.

کلیدواژه‌ها [English]

  • Compound Weir
  • Discharge Measurement
  • Hydraulic Head
  • Laboratory Flume
  • Rectangular Weir
Abbaspour A. 2001. Investigation of flow over truncated-triangular weirs. The Thesis of Master of Science Degree in Hydraulic Structure. Urmia University. (in Persian with English abstract).
2- Arvanaghi H., Mahtabi G., Valinia M., Ghavidel Z., and Azimi V. 2011. Investigation of flow discharge coefficient over semi circular-trapezoidal weir. P. 1-7. 10th Iranian Hydraulic Confrence, 8 Nov. 2011. The University of Guilan. (in Persian).
3- Aydin I., Altan-Sakarya A.B., and Sisman C. 2011. Discharge formula for rectangular sharp-crested weirs.ELSEVIER, Flow Measurement and Insrumentation, 22(1):144-151.
4- Bergmann J.M. 1963. Compound weir study. U.S. Department of the Interior, Bureau of Reclamation, Denver, United States.
5- Bos M.G. 1989. Discharge measurement structures. International Institute for Land Reclamation and Improvement, Publication 20, Wageningen, the Netherlands.
6- Jan C.D., Chang C.J., and Lee M.H. 2006. Discussion of “Design and calibration of compound sharp-crested weir, Martinez J., Reca J., Morillas M.T., and Lopez J.G. 2005”. Journal of Hydraulic Engineering, ASCE, 132(8): 868-872.
7- Kindsvater C.E., and Carter R.W. 1959. Discharge characteristics of rectangular thin-plate weirs. Transactions of the American Society of Civil Engineers,ASCE, 124:772–822.
8- Lee J.T., Chan H.C., Huang C.K., and Leu J.M. 2012. Experiments on hydraulic relations for flow over a compound sharp-crested weir. International Journal of Physical Sciences, 7(14): 2229 – 2237.
9- Martinez J., Reca J., Morillas, M.T., and Lopez J.G.2005. Design and calibration of a compound sharp-crested weir. Journal of Hydraulic Engineering, ASCE, 131(2):112-116.
10- Mousavi S.N. 2013. Investigation of discharge coefficient over arched trapezoidal and rectangular sharp-crested weirs. The Thesis of Master of Science Degree in Hydraulic Structure. The University of Tabriz. (in Persian with English abstract).
11- Swamee P.K. 1988. Generalized rectangular weir equation. Journal of Hydraulic Engineering, ASCE, 114(8): 945–949.
12- Vatankhah A.R. 2010. Flow measurement using circlular sharp-crested weirs. ELSEVIER, Flow Measurement and Insrumentation, 21(1):118-122.
CAPTCHA Image